+- XOR Userforum (https://xor-electronics.com/forum)
+-- Forum: Products (https://xor-electronics.com/forum/forumdisplay.php?fid=3)
+--- Forum: NerdSEQ (https://xor-electronics.com/forum/forumdisplay.php?fid=6)
+---- Forum: Firmware / Manual (https://xor-electronics.com/forum/forumdisplay.php?fid=11)
+---- Thread: Release Candidate Firmware V1.20 RC5 (/showthread.php?tid=456)
RE: Release Candidate Firmware V1.20 RC3 - Barney Rubble - 09-05-2019
Quick Question:
Is there a way to select samples ( Trk 7/8) with MiDi input - there was some mention of CC or perhaps PG?
RE: Release Candidate Firmware V1.20 RC3 - XORadmin - 09-05-2019
(09-05-2019, 05:21 PM)Barney Rubble Wrote: Quick Question:
Is there a way to select samples ( Trk 7/8) with MiDi input - there was some mention of CC or perhaps PG?
Yes, program change should work.
RE: Release Candidate Firmware V1.20 RC3 - Barney Rubble - 09-05-2019
Cheers mate - Program Change working like a dream
RE: Release Candidate Firmware V1.20 RC3 - joe_biomassa - 09-07-2019
Amazing update! Thanks! The ability to choose fonts really makes working with Nerdseq way easier for me!
RE: Release Candidate Firmware V1.20 RC3 - XORadmin - 09-07-2019
Just press save ;-)
Scroll down the colours and all will be fine :-)
RE: Release Candidate Firmware V1.20 RC3 - joe_biomassa - 09-07-2019
(09-07-2019, 04:16 PM)XORadmin Wrote: Just press save ;-)
Scroll down the colours and all will be fine :-)
Found it, stupid me! Thanks!
RE: Release Candidate Firmware V1.20 RC2 - grib - 09-10-2019
(08-28-2019, 04:42 PM)gr ib Wrote:(08-26-2019, 11:37 AM)Hei XORadmin Wrote:(08-06-2019, 07:51 PM)grib Wrote: Hi, I installed 1.20 RC2 and loaded a save-file from an older version (1.16 I think).
In the Automate screen there are some un-allowed values for some automation destination slots (see screenshot) and when I try to adjust these values pretty soon I will get an error as shown. The Nerdseq locks up completely and doesn't respond to any keypresses.
If I clear theH slot with DELETE it goes back to -- and I can then adjust it within the legal range with no problems.
Hey Grib,
would you mind sending me the project file so i can test it and fix the issue?
Hey, yes! Sorry I'm out of town a few days but I will send it to you as soon as I get back to nerd central.
Ok, sorry for the delay. I'm attaching the file that causes this problem. I had been playing with the automation LFOs before saving the file but I believe they were disabled when saved.
RE: Release Candidate Firmware V1.20 RC2 - gromler - 09-11-2019
Hey Everyone,
I am not sure if this has been mentioned yet, but I was playing around with getting my Launchpad Pro working and I was stumped for a little bit thinking I did something wrong and it was not working. I finally realized that by default, the tracks are all black colored. Therefore do not show up on the launchpad unless you give them all a different color. Could the track color default to gray to make launchpad use easier?
Thank you,
--Scott
RE: Release Candidate Firmware V1.20 RC2 - XORadmin - 09-11-2019
(09-11-2019, 07:47 PM)gromler Wrote: Hey Everyone,
I am not sure if this has been mentioned yet, but I was playing around with getting my Launchpad Pro working and I was stumped for a little bit thinking I did something wrong and it was not working. I finally realized that by default, the tracks are all black colored. Therefore do not show up on the launchpad unless you give them all a different color. Could the track color default to gray to make launchpad use easier?
Thank you,
--Scott
Yes i am aware of this but i think it makes only sense if you use the Launchpad with coloured patterns. Then it's full power can be used.
However, it makes definitely sense to use a slight grey colour for patterns without colour. I will try a bit what looks well and whats not in the way of the recent possible colours.
RE: Release Candidate Firmware V1.20 RC3 - gromler - 09-12-2019
Awesome!!! Thank you so much!