Release Candidate Firmware V1.24 RC12

[depaffect]

It would be awesome if the trigger info was displayed at the bottom of the screen in the trigger 16 patterns - like it is in the modular pattern screen! At the moment it just says "EXTERNAL TRIGGER 1" etc at the bottom of the trigger 16 patterns, rather than "Trigger 15ms" etc which is super helpful in the modular patterns, especially with the new trigger functionality.

Similarly, having the FX info displayed down the bottom in table screens (like it is in the modular pattern screen) would be awesome too!

[mgd]

It is possible that you upgraded from an older version (below V1.22A) then you definitely need to calibrate the inputs once anyway.

Do I understand this correctly:
My NerdSEQ was on V1.21A when I bought it and I then upgraded it to V1.23A (currently V1.24RC8). Since it was on V1.21A I should calibrate it by following the advice as of the NerdSEQ User manual pages 75 (very bottom) through page 76 and ending on page 77?

If that calibration is required, how would I have known about that? (I stumbled over the above remark kind of accidentially
 
Kind regards,
Michael

[XORadmin]

It is possible that you upgraded from an older version (below V1.22A) then you definitely need to calibrate the inputs once anyway.

Do I understand this correctly:
My NerdSEQ was on V1.21A when I bought it and I then upgraded it to V1.23A (currently V1.24RC8). Since it was on V1.21A I should calibrate it by following the advice as of the NerdSEQ User manual pages 75 (very bottom) through page 76 and ending on page 77?

If that calibration is required, how would I have known about that? (I stumbled over the above remark kind of accidentially
 
Kind regards,
Michael

You only need to recalibrate the inputs, not the outputs. It is actually a 1 minute job. half a minute to connect the 4 patch cables from the output to the input and half a minute to get to the auto-calibrate inputs screen. And don't forget to use the offset switch to the right. Nothing else needed.

I should mark this in the manual. I have a note with the release notes of the firmware that this was needed.

[XORadmin]

It would be awesome if the trigger info was displayed at the bottom of the screen in the trigger 16 patterns -  like it is in the modular pattern screen! At the moment it just says "EXTERNAL TRIGGER 1" etc at the bottom of the trigger 16 patterns, rather than "Trigger 15ms" etc which is super helpful in the modular patterns, especially with the new trigger functionality.

Similarly, having the FX info displayed down the bottom in table screens (like it is in the modular pattern screen) would be awesome too!

Actually, the trigger expander doesn't have the new functions yet. That is another job on my 2do list.

About the details in the statusbar, I know they are missing in some places. The fact is that they in the most cases share the same information, but i need to refactor actually quite a part of it to have these generic. For now I decided to skip it for this release.

[mgd]

You only need to recalibrate the inputs, not the outputs. It is actually a 1 minute job. half a minute to connect the 4 patch cables from the output to the input and half a minute to get to the auto-calibrate inputs screen. And don't forget to use the offset switch to the right. Nothing else needed.

Ah. That was simple and took almost no time
Kind regards,
Michael

[theotteryears]

is it possible to repurpose unused CV outputs into Trigger outputs?

Can we please be able to send out triggers on these?

[mgd]

To some limited extend this is currently possible. See last paragraph on page 45 ff of the manual.

Kind regards,
Michael

[theotteryears]

this refers to the CV16 expander though right? I was meaning the CV local outputs - setting a note value and using the KILL command doesn't seem to work for me here...

[XORadmin]

this refers to the CV16 expander though right? I was meaning the CV local outputs - setting a note value and using the KILL command doesn't seem to work for me here...

The Kill command resets the trigger output and is not related to the CV or MOD outpus. I would either set a MOD to 800 en the next step to 0 (if the offset is on the right) or i would maybe put a MOD 800 in a FX and a MOD 000 in the same row. It might be enough to trigger something but might also be too short.
Another option could be an envelope which can create also triggers of course (zero attack, Peak half way, sustain the same half way, zero release and the decay defines your time).
And they are probably more possibilities...a table... just take care of the voltages.

[XORadmin]

UPDATE RC9
- refactoring of the statusbar view. Added now all missing details to the stausbar in the patternscreens, table and patch screen and some other little beauty fixes

Files in the first post are updated.