XOR Userforum › Products › NerdSEQ › Firmware / Manual v
Release Candidate 1 Firmware V1.16 (RC6 UPDATE)

Thread Rating:
  • 2 Vote(s) - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
Release Candidate 1 Firmware V1.16 (RC6 UPDATE)
XORadmin Offline
Administrator
*******
Posts: 3.710
Threads: 125
Joined: Jul 2017
Reputation: 216
#31
07-30-2018, 09:45 AM
(07-30-2018, 06:29 AM)flock Wrote: About sample load, i can't really compare it with previous firmware, because i have this module since less than a week, but it gives me an error code that i will transcribe next time i'll turn on the sequencer, hopefully this evening.

Hey, if that happens again, please let me know exactly what you did and if it is repeatable. The error code is good to know but not too important. And if i can repeat it myself then it is much easier to fix, depending on the issue. Thanks
PLEASE use the search function if something have been asked or discussed before.
Every (unnessesary) forum support means less time to develop! But of course, i am here to help!  Smile
Find
Reply
XORadmin Offline
Administrator
*******
Posts: 3.710
Threads: 125
Joined: Jul 2017
Reputation: 216
#32
07-30-2018, 09:48 AM
I just updated to RC4 which fixes the new sample offset command. Now it works also if inserted on the same row as the sample note.
PLEASE use the search function if something have been asked or discussed before.
Every (unnessesary) forum support means less time to develop! But of course, i am here to help!  Smile
Find
Reply
synthbebe Offline
Junior Member
**
Posts: 13
Threads: 1
Joined: Jun 2018
Reputation: 0
#33
07-31-2018, 05:01 PM (This post was last modified: 07-31-2018, 05:05 PM by synthbebe.)
Rc4 looks like cannot load samples, I did something wrong? But Rc1 can before
Find
Reply
XORadmin Offline
Administrator
*******
Posts: 3.710
Threads: 125
Joined: Jul 2017
Reputation: 216
#34
07-31-2018, 05:10 PM
(07-31-2018, 05:01 PM)synthbebe Wrote: Rc4 looks like cannot load samples, I did something wrong? But Rc1 can before

Did you remove the sdcard and put it in again?
SD Cards with the NerdSEQ are not hot pluggable. So when removing and inserting a sd card you need to reset or power off-on the NerdSEQ. 
Pretty sure thats the problem.
PLEASE use the search function if something have been asked or discussed before.
Every (unnessesary) forum support means less time to develop! But of course, i am here to help!  Smile
Find
Reply
shledge Offline
Junior Member
**
Posts: 48
Threads: 7
Joined: Mar 2018
Reputation: 4
#35
08-01-2018, 12:11 PM
I notice the LFOs tend to slightly go in/out of sync when in tick mode - every 3-4 steps it goes out noticeably and then "snaps" back into place.
Find
Reply
XORadmin Offline
Administrator
*******
Posts: 3.710
Threads: 125
Joined: Jul 2017
Reputation: 216
#36
08-01-2018, 12:23 PM
(08-01-2018, 12:11 PM)shledge Wrote: I notice the LFOs tend to slightly go in/out of sync when in tick mode - every 3-4 steps it goes out noticeably and then "snaps" back into place.

Do you use it with Speed 1? Thats the correct divider for a 64 step pattern.
PLEASE use the search function if something have been asked or discussed before.
Every (unnessesary) forum support means less time to develop! But of course, i am here to help!  Smile
Find
Reply
shledge Offline
Junior Member
**
Posts: 48
Threads: 7
Joined: Mar 2018
Reputation: 4
#37
08-01-2018, 12:56 PM
It never fully drifts out, it's almost like there is a sync signal sent to it every few steps to "snap" it back.

I use it with 1, 4, 8 and 10 - all exhibit the same behaviour.
Find
Reply
XORadmin Offline
Administrator
*******
Posts: 3.710
Threads: 125
Joined: Jul 2017
Reputation: 216
#38
08-01-2018, 01:06 PM
(08-01-2018, 12:56 PM)shledge Wrote: It never fully drifts out, it's almost like there is a sync signal sent to it every few steps to "snap" it back.

I use it with 1, 4, 8 and 10 - all exhibit the same behaviour.

Can you send me the project please? So i can check the behaviour.
PLEASE use the search function if something have been asked or discussed before.
Every (unnessesary) forum support means less time to develop! But of course, i am here to help!  Smile
Find
Reply
XORadmin Offline
Administrator
*******
Posts: 3.710
Threads: 125
Joined: Jul 2017
Reputation: 216
#39
08-01-2018, 01:34 PM
(08-01-2018, 01:06 PM)XORadmin Wrote:
(08-01-2018, 12:56 PM)shledge Wrote: It never fully drifts out, it's almost like there is a sync signal sent to it every few steps to "snap" it back.

I use it with 1, 4, 8 and 10 - all exhibit the same behaviour.

Can you send me the project please? So i can check the behaviour.

I just tested it myself and all seems fine. My guess is that the bitrate of the LFO is set to 4 or 2 maybe? Because then i get exactly the behaviour you describe. Speed 1 and bitrate to 16 and there should be no issue.
PLEASE use the search function if something have been asked or discussed before.
Every (unnessesary) forum support means less time to develop! But of course, i am here to help!  Smile
Find
Reply
synthbebe Offline
Junior Member
**
Posts: 13
Threads: 1
Joined: Jun 2018
Reputation: 0
#40
08-01-2018, 02:39 PM
(07-31-2018, 05:10 PM)XORadmin Wrote:
(07-31-2018, 05:01 PM)synthbebe Wrote: Rc4 looks like cannot load samples, I did something wrong? But Rc1 can before

Did you remove the sdcard and put it in again?
SD Cards with the NerdSEQ are not hot pluggable. So when removing and inserting a sd card you need to reset or power off-on the NerdSEQ. 
Pretty sure thats the problem.
Haha, I know that before I buy nerdseq because I visited user forum, so I know it's not the business of that, anyway It's ok now, may be I forget copy setting into the card or may be I also put another folder into the firmware folder.......
Find
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)